Proper nitro engine break-in is critical for long-lasting performance of your RC. Every new nitro engine should undergo a break-in procedure. Breaking in a nitro engine takes anywhere from one to two hours and about 3-5 tanks of nitro fuel. If you do the nitro engine break-in properly, the up-keep on your RC vehicle is less costly than if the procedure is done hastily and incorrectly. Be patient.
Answer: For your nitro engine break-in, choose a clean, flat, paved or smooth surface. You’ll be doing the initial break-in with the body off so you don’t want to be kicking up dirt or doing flips during break-in. During the first couple of tanks of fuel focus on varying and limiting your speed. Don’t run your engine past half-throttle. Don’t run at a constant speed.
During break-in deposits build up and can foul out the glow plug so your engine might seem like it’s stalling or not running properly. This is normal. Proper break-in alleviates these symptoms. Do have an extra glow plug or two handy in case you need them.
Operate Safely
Here are simple safety checks you need to do before starting:
Turn on the Controller First
Turn your transmitter/controller on first followed by the receiver on the RC. When finished running your RC, turn the receiver off first, then the controller. This sequence will keep your nitro RC from running amok if someone nearby is running on the same frequency. Do yourself a favor though and check frequency before running your RC.
Put The Engine in Neutral
Move the throttle forward and reverse to ensure your nitro engine is in neutral and is in the idle position when the throttle is released.
Check Your Steering
Move the steering controls from side to side. If steering seems sluggish or hesitant, replace the receiver’s batteries before proceeding.
Prime Your Nitro Engine
Start up your RC. Watch to see if fuel is moving through the lines. If fuel doesn’t reach the carburetor after 3-5 seconds place and release your finger over the tip of the exhaust for a couple of seconds to help the engine start. This is known as priming the engine. Be careful when doing so because if too much fuel goes into the engine when priming, it will flood causing the engine to lock up.
If the engine does flood use your glow plug wrench to remove the glow plug. Place a rag over the engine head. If equipped, use your electric starter. Start the engine to get the remaining fuel out and wipe off the head with a dry towel to remove any remaining fuel. Reinstall the glow plug and start on the first tank of the break-in process. Your nitro engine shoudn’t be primed for more than 1-2 seconds at a time to avoid flooding.
Do Five Tank Nitro Engine Break-in
With each tank of fuel you’ll increase the amount and duration of throttle. Use these tank-by-tank guidelines for your nitro engine break-in.
Tank 1
Give the engine one-quarter throttle slowly for 2 seconds. Apply the brakes. If you pull back on the throttle too fast you may cause your engine to stall.
When there is a nice trail of blue smoke coming from the exhaust it means your fuel mixture is properly set and the engine is being lubricated. If no smoke is present, richen the fuel mixture by giving the air/fuel mixture needle a quarter turn until smoke is present.
Continue running the first tank of fuel, repeatedly giving it one-quarter throttle then braking until it is almost empty. Do not run the tank dry because this will result in a burned out glow plug from the fuel mixture being too lean and can also lead to damage from high engine temperatures.
Shut off the engine by pinching the fuel line to the carburetor and let it cool down for about 10-15 minutes before you start on your next tank of fuel.
Tank 2
Advance to half-throttle for 2-3 seconds for the second tank of fuel. Remember to accelerate smoothly through the entire break-in process. Do this repeatedly as long as you have fuel. When the second tank is done repeat the shut-off and cool-down ste
Gas or Electric? If gas, then read the above post ^^^. If electric, a lot of motors came already broken in. Otherwise, I hooked a battery directly to the motor and let it run for a few minutes until the armature (sp?) seated itself in the brushes.
November 30th, 2010 at 3:23 am
Proper nitro engine break-in is critical for long-lasting performance of your RC. Every new nitro engine should undergo a break-in procedure. Breaking in a nitro engine takes anywhere from one to two hours and about 3-5 tanks of nitro fuel. If you do the nitro engine break-in properly, the up-keep on your RC vehicle is less costly than if the procedure is done hastily and incorrectly. Be patient.
Answer: For your nitro engine break-in, choose a clean, flat, paved or smooth surface. You’ll be doing the initial break-in with the body off so you don’t want to be kicking up dirt or doing flips during break-in. During the first couple of tanks of fuel focus on varying and limiting your speed. Don’t run your engine past half-throttle. Don’t run at a constant speed.
During break-in deposits build up and can foul out the glow plug so your engine might seem like it’s stalling or not running properly. This is normal. Proper break-in alleviates these symptoms. Do have an extra glow plug or two handy in case you need them.
Operate Safely
Here are simple safety checks you need to do before starting:
Turn on the Controller First
Turn your transmitter/controller on first followed by the receiver on the RC. When finished running your RC, turn the receiver off first, then the controller. This sequence will keep your nitro RC from running amok if someone nearby is running on the same frequency. Do yourself a favor though and check frequency before running your RC.
Put The Engine in Neutral
Move the throttle forward and reverse to ensure your nitro engine is in neutral and is in the idle position when the throttle is released.
Check Your Steering
Move the steering controls from side to side. If steering seems sluggish or hesitant, replace the receiver’s batteries before proceeding.
Prime Your Nitro Engine
Start up your RC. Watch to see if fuel is moving through the lines. If fuel doesn’t reach the carburetor after 3-5 seconds place and release your finger over the tip of the exhaust for a couple of seconds to help the engine start. This is known as priming the engine. Be careful when doing so because if too much fuel goes into the engine when priming, it will flood causing the engine to lock up.
If the engine does flood use your glow plug wrench to remove the glow plug. Place a rag over the engine head. If equipped, use your electric starter. Start the engine to get the remaining fuel out and wipe off the head with a dry towel to remove any remaining fuel. Reinstall the glow plug and start on the first tank of the break-in process. Your nitro engine shoudn’t be primed for more than 1-2 seconds at a time to avoid flooding.
Do Five Tank Nitro Engine Break-in
With each tank of fuel you’ll increase the amount and duration of throttle. Use these tank-by-tank guidelines for your nitro engine break-in.
Tank 1
Give the engine one-quarter throttle slowly for 2 seconds. Apply the brakes. If you pull back on the throttle too fast you may cause your engine to stall.
When there is a nice trail of blue smoke coming from the exhaust it means your fuel mixture is properly set and the engine is being lubricated. If no smoke is present, richen the fuel mixture by giving the air/fuel mixture needle a quarter turn until smoke is present.
Continue running the first tank of fuel, repeatedly giving it one-quarter throttle then braking until it is almost empty. Do not run the tank dry because this will result in a burned out glow plug from the fuel mixture being too lean and can also lead to damage from high engine temperatures.
Shut off the engine by pinching the fuel line to the carburetor and let it cool down for about 10-15 minutes before you start on your next tank of fuel.
Tank 2
Advance to half-throttle for 2-3 seconds for the second tank of fuel. Remember to accelerate smoothly through the entire break-in process. Do this repeatedly as long as you have fuel. When the second tank is done repeat the shut-off and cool-down ste
November 30th, 2010 at 6:09 pm
Gas or Electric? If gas, then read the above post ^^^. If electric, a lot of motors came already broken in. Otherwise, I hooked a battery directly to the motor and let it run for a few minutes until the armature (sp?) seated itself in the brushes.